Skip to main content

High-temperature electronics? That's hot

High-temperature electronics? That's hot :


A new organic plastic allows electronics to function in extreme temperatures without sacrificing performance.
From iPhones on Earth to rovers on Mars, most electronics only function within a certain temperature range. By blending two organic materials together, researchers at Purdue University could create electronics that withstand extreme heat.
This new plastic material could reliably conduct electricity in up to 220 degrees Celsius (428 F), according to a paper published Thursday in the journal Science.
"Commercial electronics operate between minus 40 and 85 degrees Celsius. Beyond this range, they're going to malfunction," said Jianguo Mei, a professor of organic chemistry at Purdue University. "We created a material that can operate at high temperatures by blending two polymers together."
One of these is a semiconductor, which can conduct electricity, and the other is a conventional insulating polymer, which is what you might picture when you think of regular plastic. To make this technology work for electronics, the researchers couldn't just meld the two together -- they had to tinker with ratios.
"One of the plastics transports the charge, and the other can withstand high temperatures," said Aristide Gumyusenge, lead author of the paper and graduate researcher at Purdue. "When you blend them together, you have to find the right ratio so that they merge nicely and one doesn't dominate the other."
The researchers discovered a few properties that are essential to make this work. The two materials need to be compatible to mixing and should each be present in roughly the same ratio. This results in an organized, interpenetrating network that allows the electrical charge to flow evenly throughout while holding its shape in extreme temperatures.
Most impressive about this new material isn't its ability to conduct electricity in extreme temperatures, but that its performance doesn't seem to change. Usually, the performance of electronics depends on temperature -- think about how fast your laptop would work in your climate-controlled office versus the Arizona desert. The performance of these new polymer blend remains stable across a wide temperature range.
Extreme-temperature electronics might be useful for scientists in Antarctica or travelers wandering the Sahara, but they're also critical to the functioning of cars and planes everywhere. In a moving vehicle, the exhaust is so hot that sensors can't be too close and fuel consumption must be monitored remotely. If sensors could be directly attached to the exhaust, operators would get a more accurate reading. This is especially important for aircraft, which have hundreds of thousands of sensors.
"A lot of applications are limited by the fact that these plastics will break down at high temperatures, and this could be a way to change that," said Brett Savoie, a professor of chemical engineering at Purdue. "Solar cells, transistors and sensors all need to tolerate large temperature changes in many applications, so dealing with stability issues at high temperatures is really critical for polymer-based electronics."
The researchers will conduct further experiments to figure out what the true temperature limits are (high and low) for their new material. Making organic electronics work in the freezing cold is even more difficult than making them work in extreme heat, Mei said.

Comments

Post a Comment

Popular posts from this blog

Size matters: New data reveals cell size sparks genome awakening in embryos

Transitions are a hallmark of life. When dormant plants flower in the spring or when a young adult strikes out on their own, there is a shift in control. Similarly, there is a transition during early development when an embryo undergoes biochemical changes, switching from being controlled by maternal molecules to being governed by its own genome. For the first time, a team from the Perelman School of Medicine at the University of Pennsylvania found in an embryo that activation of its genome does not happen all at once, instead it follows a specific pattern controlled primarily by the various sizes of its cells. The researchers published their results this week as the cover story in  Developmental Cell . In an early embryo undergoing cell division, maternally loaded RNA and proteins regulate the cell cycle. The genomes of the zygote -- a term for the fertilized egg -- are initially in sleep mode. However, at a point in the early life of the embryo, these zygotic nuclei "wake...
Post a Comment
Read more

Home births as safe as hospital births: International study suggests

A large international study led by McMaster University shows that low risk pregnant women who intend to give birth at home have no increased chance of the baby's perinatal or neonatal death compared to other low risk women who intend to give birth in a hospital. The results have been published by  The Lancet 's  EClinicalMedicine  journal. "More women in well-resourced countries are choosing birth at home, but concerns have persisted about their safety," said Eileen Hutton, professor emeritus of obstetrics and gynecology at McMaster, founding director of the McMaster Midwifery Research Centre and first author of the paper. "This research clearly demonstrates the risk is no different when the birth is intended to be at home or in hospital." The study examined the safety of place of birth by reporting on the risk of death at the time of birth or within the first four weeks, and found no clinically important or statistically different risk between home...
Post a Comment
Read more

Molecular adlayer produced by dissolving water-insoluble nanographene in water

Molecular adlayer produced by dissolving water-insoluble nanographene in water : "Nanographene incorporated micelle capsules" can be prepared by simply pulverizing and mixing nanographene with amphiphilic V-shaped anthracene molecules in water at room temperature. Even though nanographene is insoluble in water and organic solvents, Kumamoto University (KU) and Tokyo Institute of Technology (Tokyo Tech) researchers have found a way to dissolve it in water. Using "molecular containers" that encapsulate water-insoluble molecules, the researchers developed a formation procedure for a nanographene adlayer, a layer that chemically interacts with the underlying substance, by just mixing the molecular containers and nanographene together in water. The method is expected to be useful for the fabrication and analysis of next-generation functional nanomaterials. Graphene is a single layer of carbon atoms arranged in sheet form. It is lighter than metal wit...
Post a Comment
Read more